Page 1 of 2 12 LastLast
Results 1 to 5 of 6

Thread: LTE RAN Radio Network Parameters, L14A

  1. #1
    Level 3 Users
    Join Date
    Jul 2012
    Location
    CIS
    Posts
    307
    Post Thanks / Like
    Credits
    8,646
    Rep Power
    8

    Post LTE RAN Radio Network Parameters, L14A

    LTE RAN Radio Network Parameters, L14A:

    Document describes the LTE L14A parameters.

    Radio Network Parameters
    This sheet lists and gives information about the LTE RAN Parameters.

    The following information is presented for each parameter:





    Managed Area Managed Area the attribute belongs to.
    MO Class Name Managed object class the attribute belongs to.
    Parameter Name Attribute name as defined in the MOM.
    Sequence Length Maximum length for parameter arrays.
    Parameter Description "Contains following information:
    - Brief description of the parameter.
    - When a parameter change will take effect.
    - If there are dependencies or restrictions in relation to other parameters.
    A dependency means that there are other parameters that may need to be changed to be consistent with the new value.
    A restriction means that there is a relation to another parameter that must be preserved.
    This information is not applicable for the data type Struct."
    Data Type "Data type for the parameter, e.g., long, string.
    If the data type is Struct it is described on the Struct Parameters sheet, see section 2.2"
    Range and Values Valid value range or values for the parameter.
    Default Value Default value, as initially set by the system, if not explicitly set at MO creation.
    Unit Specifies the unit of the parameter
    Resolution Specifies the step size or granularity of the parameter if applicable.
    ReadOnly Specifies whether or not the parameter can be changed by the operator.
    Restricted Restricted means that, once the corresponding MO has been created, the parameter becomes read only and can only be modified by recreating the MO.
    Mandatory Indicates whether or not the parameter is mandatory to configure at creation of the corresponding MO. For mandatory parameters no default value is defined.
    Persistent Indicates whether or not the parameter is stored persistently in the database of a node. Persistent data will survive a node restart.
    Change Take Effect Indicates when the change will take effect
    Disturbances "Indicates if the action has the side effect that the resource
    needs to be taken out of service or affects traffic in any other way."
    Dependencies "Indicates if there are other parameters that may
    need to be changed to be consistent with the new value."
    Deprecated Indicates whether the parameter is deprecated.
    Bulk CM Included Indicates if the parameter is visible in the Bulk CM interface.
    CPP Parameter Indicates whether the parameter is a CPP parameter.

    Struct Name The name of the Struct. Corresponds to the Data type column on the Radio Network Parameters sheet, see section 2.1
    Parameter Name Attribute name as defined in the MOM.
    Sequence Length Maximum length for parameter arrays.
    Description "Contains following information:
    - Brief description of the parameter.
    - When a parameter change will take effect."
    Data Type Data type for the parameter, e.g., long, string.
    Range and Values Valid value range for the parameter.
    Default Value Default value, as initially set by the system, if not explicitly set at MO creation.
    Unit Specifies the unit of the parameter
    Resolution Specifies the step size or granularity of the parameter if applicable.
    Dependencies "Indicates if there are other parameters that may
    need to be changed to be consistent with the new value."
    Deprecated Specifies whether the parameter is deprecated


    Similar Threads:
    Attached Files Attached Files

  2. Minimum 5G Requirements
    CQI PMI and RI - LTE Quality Indicators
    Difference between PUCCH and PUSCH
    LTE Device Ecosystem - July 2017
    Why VoLTE finally being rolled out ?
  3. #2
    Level 1 Users
    Join Date
    Aug 2015
    Posts
    16
    Post Thanks / Like
    Credits
    285
    Rep Power
    0
    The document about RAN parameter is what I am looking for, cheers


  4. #3
    Junior Member
    Join Date
    Sep 2015
    Posts
    2
    Post Thanks / Like
    Credits
    352
    Rep Power
    0
    Hi Guys,

    I am a newbie, and I would love to get access to downloading the file. I am an optimization engineer and the information could really help me.
    For sure I am at your disposal for any optimization topics involving E// RAN.

    Balanello.


  5. Likes wijayadny, Aisha Javed liked this post
  6. #4
    Level 1 Users
    Join Date
    Mar 2015
    Posts
    4
    Post Thanks / Like
    Credits
    10
    Rep Power
    0
    Is this for RAN only ?. How about core PS and IMS.


  7. Likes charly liked this post
  8. #5
    Level 1 Users
    Join Date
    Sep 2016
    Posts
    16
    Post Thanks / Like
    Credits
    14
    Rep Power
    0
    good.............................................. .......................


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •